Workbench | Blood, Sweat, and Sawdust

January 12, 2015

Jointing Long Edges by Hand

Jointing long edges by hand ended up being a little more work than I expected. Yellow pine planes nicely, but it’s resinous nature creates a lot of friction. It also required spending a little extra time cleaning my tools free of the resin.

My current workbench couldn’t support the long boards for edge jointing. I worked around this by cutting a scrap board to the approximate height of my vise and clamping that to the opposite leg. This allowed the other end of the board a place to rest.

From there it was just a matter of ripping these boards to width on the band saw. These narrow boards gave much less fuss than the original 11″ wide boards. The resulting boards end up being nearly quartersawn. The board shown above was the worst of the bunch. As a result there’s no need to joint the faces of these boards. I’ll just run both sides through the planer and glue them up.

Stay tuned.

You can find links to my other Roubo posts here: Project Index

January 7, 2015

The Tension Builds…

Ripped and stickered

I decided to go ahead and rip all of my 2×12 stock in half to speed up the drying process. I knew there would be some tension built up in some of the boards, but a few of them where downright scary. I had one split for the last two feet of the board. This caused one half to slide off my roller stand. The back end kicked up and hit the blade guards fairly hard. No damage was done, but it gave me quite a scare. The split shifted the cut a few inches, making one have too narrow to use for my top. I’ll save this for my long stretchers.

I sorted and labeled all of my boards, saving the best for the front and back of the top. If you’re ripping construction lumber, keep a few extra roller stands handy. Also, be prepared to clean your tools free of pitch when you’re finished. You might even consider buying an extra band saw blade for this project. Simple Green took care of the blade and a ruler scraped the tires free of debris.

You can find links to my other Roubo posts here: Project Index

January 4, 2015

2015 Roubo Build

I’ve been very unhappy with my workbench for quite some time. The MDF top sags due to the weight of the vise. The top is too thin for holdfasts. And the work holding is generally subpar.

I’ve struggled over designs to the point of exhaustion. I eventually settled on the French Roubo with dovetailed through tenons as seen in infamous Plate 11. After much thought, I decided that building furniture was more important to me than a stunning workbench. I dropped the dovetails in favor of stub tenons. This will allow me to build the bench in significantly less time.

There is no desire for rock hard or exotic lumber here. I settled for cost-effective, Soutern Yellow Pine. I had to sort through an entire stack of 2×12’s at the local Borg, but I was able to find enough suitable boards to supply an 8 ft long, 4″ thick top. This left me enough greenbacks in my budget for a Classic Bench Crafted leg vise.

Stay tuned!

Hauling long, heavy boards in my short-bed pickup always makes me nervous

You can find links to my other posts regarding the Roubo build below:

Part 1: The Tension Builds

Part 2: Jointing and Ripping

Part 3: Lamination without Lamentation

Part 4: Sketchup to the Rescue

Part 5: Benchtop Lamination Followup

Part 6: Milling the Beams for the Top

Part 7: Sketchup Design Completion

Part 8: Jointing Wide Edges

Part 9: A Quick Roubo Build Update

Part 10: When Things Come Together

Bonus: Crap Wood for Good Workbenches

Bonus: Jointing Wide Edges by Hand: Companion Video

January 4, 2015

The Roubo Workbench Build

Roubo Workbench Sketchup

I’ve been very unhappy with my workbench for quite some time. The MDF top sags due to the weight of the vise. The top is too thin for holdfasts. And the work holding is generally subpar.

There is no desire for rock hard or exotic lumber here. I settled for cost-effective, Southern Yellow Pine. I had to sort through an entire stack of 2×12’s at the local Borg, but I was able to find enough suitable boards to supply an 8 ft long, 4″ thick top. This left me enough greenbacks in my budget for a Classic Bench Crafted leg vise.

Stay tuned!